New SawSmith Owner

More
11 years 2 months ago #9471 by johnmccrossen
johnmccrossen replied the topic: Re:New SawSmith Owner
rsdiggs,

You can still get a copy of the owners manual and parts list from Shopsmith Customer Service. You can find the info on the Shopsmith web page. I scored on a 1959 model awhile back for $10.00 and was able to get it functional. I had many of the same issues that it sounds like you have. Lots of elbow grease and a few parts like new drive belt and spindle bearings but not too much else so far. My biggest problem was to unstick the radial arm from the pivot post. That was difficult. I still need to paint mine to match the two Mark V goldies that I have but the project is set aside for now. Anyway, good luck and have fun. It sounds like you got some good accessories that will be fun to get rehabilitated. John McCrossen

Please Log in to join the conversation.

  • SDSSmith
  • SDSSmith's Avatar Topic Author
  • Offline
  • Senior Boarder
  • Senior Boarder
More
11 years 1 month ago #9520 by SDSSmith
SDSSmith replied the topic: Re:New SawSmith Owner
I found a copy of the manual. I am not sure I care, but I have not been able to release the headstock to rotate it on the arm.

Please Log in to join the conversation.

More
11 years 1 month ago #9523 by johnmccrossen
johnmccrossen replied the topic: Re:New SawSmith Owner
rsdiggs,
The only way I was able to free up the arm to rotate (once the release pin was removed) was to keep soaking the tube with penetrating oil from the top. I removed the large snap ring on the top of the pivot tube so the penetrant could get directly between the tube and the casting where it pivots. After soaking for several days, I just kept jerking on the arm and bumping it with a dead-blow hammer. (Almost tipped it over a few times also). Anyway it finally moved much to my surprise. Then the more I worked it, the better it got. Unfortunately after making a new table and getting it to where I could actually make a cut with it, I found other things to play with, so now it's sort of resting in a corner. It was still a fun project. Good luck. John McCrossen

Please Log in to join the conversation.

  • SDSSmith
  • SDSSmith's Avatar Topic Author
  • Offline
  • Senior Boarder
  • Senior Boarder
More
11 years 1 month ago #9529 by SDSSmith
SDSSmith replied the topic: Re:New SawSmith Owner
My arm releases and rotates on the column just fine. Up and down on the column are great. I just haven't been able to rotate the headstock (for ripping). I have freed up the locking mechanism, but it still won't rotate.

Please Log in to join the conversation.

More
11 years 1 month ago #9534 by johnmccrossen
johnmccrossen replied the topic: Re:New SawSmith Owner
rsdiggs,

I misunderstood which part you can not move.

You might try removing the locking pin mounting assembly and squirting penetrant down into the hole where the pin goes into the yoke. You can also try squirting penetrant between the mounting plate and the yoke, maybe it will soak in there. I ended up removing the motor and drive unit so I could fix the varispeed pulleys and replace the spindle bearings. This made it easier to work on the yoke pivot. In looking at the exploded view of the parts list today, I noticed that there is a set screw in the locknut for the pivot bearing. I would think that if you loosened the set screw, you could then loosen the locknut a little and that should allow you to free things up. I would clearly mark the locknut position before if you try this so you can get it back to the original position. I don't know if these suggestions will help you, but good luck anyway. John McCrossen

Please Log in to join the conversation.

  • SDSSmith
  • SDSSmith's Avatar Topic Author
  • Offline
  • Senior Boarder
  • Senior Boarder
More
11 years 1 month ago #9546 by SDSSmith
SDSSmith replied the topic: Re:New SawSmith Owner
Thanks John, today I had some time and completely removed the locking mechanism. I was able to get the headstock turning. All seems to function now,just at matter of cleaning it up and putting it back on the stand. Thanks again.

Please Log in to join the conversation.

Time to create page: 0.247 seconds

Administrator

Free Joomla! template by L.THEME